Aggregate Base Testing Technician-ASTM Methods Exam Prep
Free practice questions

Free ACI-AGGREGATE-BASE Practice Questions

10 exam-style questions with answers and explanations, straight from our 1,030-question bank. Tap an answer to check yourself. When you're ready, take the scored version in the free practice test.

Start the free practice test → ★★★★★4.9/5 from 2,400+ candidates · No signup

These 10 free ACI-AGGREGATE-BASE questions are organized by exam domain, so you can see how each part of the Aggregate Base Testing Technician-ASTM Methods blueprint is tested. Reveal the answer and explanation under each question.

Domain 1: ASTM D75/D75M-Standard Practice for Sampling Aggregates

Question 1

Sieve analyses of two properly reduced test portions from one stockpile field sample agree closely. The sampling record shows that every increment came from the toe, where coarse particles had accumulated. How should the matching results be interpreted?

Show answer & explanation

Correct answer: B - The tests can agree even when the field sample overrepresents coarse particles.

Question 2

At an operating aggregate conveyor, a sampler plans to place belt-shaped templates around a segment and remove the material by hand. The operator offers to slow the conveyor rather than stop production. Which work arrangement is acceptable?

Show answer & explanation

Correct answer: C - Stop the belt and prevent unexpected restart before placing the templates.

Domain 2: ASTM C702/C702M-Standard Practice for Reducing Samples of Aggregate to Testing Size

Question 3

A fine-aggregate sample has free surface moisture and is ready for reduction. A mechanical splitter and a clean quartering surface are available. Which procedure allows a representative test portion to be obtained without first drying the sample?

Show answer & explanation

Correct answer: D - Quarter the moist sample, preserving the fines belonging to the retained portions.

Domain 3: ASTM D4318-Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils

Question 4

During a plastic-limit determination on soil passing the No. 40 sieve, a thread reaches 3.2 mm within the prescribed rolling time but remains smooth and flexible. The technician should now:

Show answer & explanation

Correct answer: A - Reform the soil and continue rolling toward the crumbling endpoint.

Question 5

The groove in a liquid-limit specimen closes over 13 mm after 23 blows, but the technician sees the entire soil pat slide across the cup rather than flow at the groove. The cup drop and operating rate have been verified. How should this observation be treated?

Show answer & explanation

Correct answer: C - Exclude this closure, remix and reform the soil, and repeat the trial.

Domain 4: ASTM D7928-Standard Test Method for Particle-Size Distribution (Gradation) of Fine-Grained Soils Using the Sedimentation (Hydrometer) Analysis

Question 6

Minutes after agitation, a hydrometer suspension develops visible flocs and clears unusually quickly. Its calculated fine fraction is much smaller than expected. Which mechanism best explains both observations?

Show answer & explanation

Correct answer: B - Inadequate dispersion left fine particles settling together as larger units.

Domain 5: ASTM D2216-Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

Question 7

An ASTM D2216 Method B worksheet lists an empty container mass of 30.00 g and a separate lid mass of 5.00 g. The container, lid, and moist soil together weigh 173.00 g. After drying to constant mass and cooling, the same container and lid with the dry soil weigh 155.00 g. What water content belongs in the report?

Show answer & explanation

Correct answer: C - 15.0%

Domain 6: ASTM D1557-Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft³ (2,700 kN-m/m³))

Question 8

The cumulative percentages retained by dry mass are 34% on the No. 4 sieve, 28% on the 3/8-in. sieve, and 12% on the 3/4-in. sieve. The specification requires ASTM D1557 but does not designate Method A, B, or C. Select the applicable mold, test fraction, and compaction sequence.

Show answer & explanation

Correct answer: D - 6-in. mold; material passing 3/4 in.; five layers with 56 blows per layer.

Question 9

To prepare a fresh specimen for a modified-effort compaction point, 2,700 g of moist soil at 8.0% water content must be brought to 12.0% water content. No soil or water will be lost during mixing and sealed conditioning. How much water must be added?

Show answer & explanation

Correct answer: D - 100 g

Domain 7: ASTM D698-Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft³ (600 kN-m/m³))

Question 10

In a standard-effort compaction series, the wetter of two specimens has a higher moist density but a lower dry density. Both specimens received the prescribed effort, and their mass, volume, and water-content records have been checked. How can this combination occur?

Show answer & explanation

Correct answer: A - Additional water can raise moist density while dry-solid mass per unit volume falls.

That's 10 of 1,030

The full bank has 1,020 more ACI-AGGREGATE-BASE questions with explanations.

Continue in the free practice test →

View plans